Cannot update/save settings to CMC
Hi First up I'm new to blades I have recently acquired a dell M1000e with 2 CMC4.5 a iKvm and a couple of blades second hand when I access the rack via the web portal using root and calvin I am unable...
View ArticleR420 chassis heating due raid controller card
hiwe purchased 6 servers from dell india. we are facing a severe heating issue on top of the chassis above the raid card with all these 6 servers.server configurationR420 - single hexcore processor 2.2...
View Articlemanuals /BIOS etc for a Dell DCS6005 3-node AMD server
Hi,Maybe a desperate move to seek help here since the official support.dell.com has nothing about a Dell PowerEdge 6005 server. This is a -most likely- custom made server for a customer. It has 3-nodes...
View ArticleBlade assistance
Hi all,I am hoping someone may be able to help. Currently we use Dell r620 hosts and EqualLogic arrays. These run a VMware cluster.I am looking at perhaps moving to a blade array system, as it will...
View ArticlePE2950III Processor Support
Hello!I read someplace that the PE2950III with latest BIOS can support 5600 series Xeons.Can anyone confirm?Thanks!Mike
View ArticlePoweredge T110 and installing video card
I wanted to see if anyone has had any updates regarding putting a video card into poweredge T110 and if you have what kind of video card did you use? In order for you to install and use the video...
View ArticleDell Power Edge does not start up
I have a Dell R720.whenenergized theserver.The buttonwith the letter"i"thatis in frontstays onanddoes not go outmore.Thenthe serverdoes notturn on.The energycomes from aUPSandis...
View ArticleProblem during installing Windows Server 2008 at my Server dell
Hello guy!I have a Server Dell PowerEdge T620I did a Raid 5 for 3 Hard disk drive WD30EFRX Red drive ( each 4TB)When I'm installing Windows Server 2008, not find hard disk, which make...
View ArticleDELL R710 - 2 network cards out of 4, if active cannot be seen at the LAN
Hello AllI have a server R710 and it has 4 network cards on it.I have deactivated 2 out of the 4 network cards that come from the manufacture and for the other 2 the configuration is as follows:Network...
View ArticleWake On LAN
Hi Chriscan you help me. How can i set wake up on lan. In bios, i only see security systerm/AC recovery. I need set up it wake up on lan. Please help me. thanks a lot.
View ArticleVRTX and M620
Hi everybody,I have a VRTX with two M620s, one of the M620s gives me an error during post. the error says; Warning : Chassis verification failure. System configuration may not be correct.I need help...
View ArticlePower edge 1950 VGA Driver- Win 2000 Sever
Trying to locate a Driver for a PowerEdge 1950 Service Tag <ADMIN NOTE: Service tag removed as per privacy policy> on board VGA chip running Win 2000 Sever-Service pack 4, or alternative what...
View ArticleRAC0503 and RAC0501 with T620 and H310
I have a T620 with one Perc H310 connected to the backplane. In the iDrac when I go to storage I get the following error:RAC0501: There are no physical disks to be displayed. 1. Check if the host...
View ArticleDell PowerEdge 2950 II - Unsupported cpu combination System halted
I bought two new processors for my PowerEdge 2950 II and the place get the error below:Unsupported cpu combinationSystem haltedThe processors are the model Xeon E5440, socket LGA771.The BIOS version is...
View ArticleDell Power Edge 2950 with Dual Core 1.86ghz proc *2
I am trying to upgrade this server and after looking at CPU support it looks like this may take up to 3.16ghz Xeon quad core proc.Can some one verify if either 2.66 Mhz or 3.16Mhz quad core CPUs work...
View ArticleCannot Install Windows Server on Dell T420
I have a Dell server and it was running as an EXSi server. I am in the process of reassigning it to be a HyoerV server. Unfortunately, I was unable to install HyperV or Windows servers. I have tried...
View ArticlePurchased Used Poweredge R710 - Came with custom firmware.. how can I reflash...
I purchased a Used Poweredge R710 today with no drives.Turns out this was used for an arcsight logger.Service tag comes up: PowerEdge R710Service Tag: HNV0DQ1 | Express Service Code: 38448107641 I...
View ArticleT410, 'Press F1 to continue, F2 to enter setup'
Last week our PE T410 had a PCIE failure on bus 0 and reboot. It hung on 'Press F1 to continue, F2 to enter setup'. Dell came out and replaced the system board but it still hangs on 'Press F1 to...
View ArticleError code showing when there is not an error on PowerEdge 2950II
So a while back I posted here asking if I could replace the backplane of my poweredge 2950 without messing anything up (raid wise). The answer I got was yes since it is all hardware based, which I had...
View ArticleDell Poweredge 2950 III not recognizing 32gb of memory
i put 8 sticks of 4gb in there and it only detects 28 gbsays an error about dimm slot 7 being disabledis this a bios setting or version issue?
View Article