poweredge m100e
bonjour,comment basculer du mode ligne de commande vers le mode graphique au niveau du cmc?how to switch between mode cli and graphic interface on the cmc?
View ArticleContent of customized iso of ESXi 5.0
HiI have read in the Important Information section of the VMware ESXi 5.0 Update 3 Recovery Imagethat it does not contain the Dell OpenManage Server Administrator Agent. I would like to know if it only...
View ArticleCannot download SUU-32_15.07.200.30.iso
I have taken over support on a PowerEdge R710 server. I am attempting to do a firmware update, but I cannot download the required iso file. I have been trying for literally 24 hours, and the download...
View ArticlePowerEdgge T610 Memory Upgrade Configuration 16GB quad rank ECC RDIMM
Without powering off the PE T610, I can't see what BIOS setting (Advanced ECC, Optimized, Mirrored). The iDRAC displays the memory modules installed, but doesn't indicate their configuration. So I must...
View ArticlePowerEdge T110 Memory Upgrade
Hello,I have a PowerEdge T110 with 2x2GB RAM installed, and I was planning on upgrade it by adding two more 4GB RAM modules, bringing the total memory amount to 12GB.From the manual I can see that the...
View ArticleDell System Hardware & Software Updates for July 27 - 31, 2015
Popular DownloadsDSET - Dell Server E-Support ToolDell Support Live Image 2.2OpenManage Server Administrator (OMSA)OpenManage Essentials (OME) 2.0.1Servers & StorageVRTX Chassis Infrastructure...
View ArticlePE m610 blade server A runtime critical stop occurred.
Hi,i have m1000e enclosure with 16 m610 servers installed,one of the servers halted a gave a blue screen, the CMC web interface gives A runtime critical stop occurred. warning in the health and...
View ArticleClik here to view.
Cannot apply DUP for iDRAC on M710HD
Hi,I am trying to update the drac on four m710HDs and cannot get the 3.75 version to install (up from 3.65). Error is in the shot below, which is a really weird message. Happens on all machines.Doesn't...
View ArticleQ Logic single port card is not working
Hi,I have facing some issue with q logic single port HBA card in PE-710. In this HBA card is not working and all three LED IS now blinking at once. now server is in production. RegardsGS
View ArticleCannot update FW on Intel I350-t using LCC
I have a similar issue.several Dell R720xd servers with a Gigabit 4P I350-t Adapter, and i can't get the firmware updated to 16.5.20I am using the latest SUU dvd, from witin the lifecycle controller....
View ArticleDELL PE R200 + 4 TB
Hi,Is it possible to connect 2 X 4 TB HDD directly to the onboard SATA ports and start using it?I wish to convert it to a simple file server.Thanks
View ArticlePowerEdge M610 EOL
Anyone could advise me about Blade server M610 end of life?many thanks,-TC-
View ArticleBasic Remote Management possibilities on T20 server
Hello,We have bought a T20 server. I would like to use a convencional basic remote functions etc. power on/ power off /reboot/ watch hardware healthy and remote console. Can someone tell it possible to...
View ArticleiDrac remote session ip log
Hello,I wanted to check something that is a potential security issue for me.When I connect to iDrac on my PowerEdge R620 (Version 7.4.0), is there any log kept (either on the iDrac card or on the...
View ArticleC6145, Ubuntu: omreport no controllers found
I'm running Ubuntu 14.04, 64bit, on a C6145. I installed srvadmin-all 7.4 via the directions at linux.dell.com/repo/community/ubuntu/. It installed successfully.However, when I run...
View ArticlePowerEdge T110 Heat Sink Socket Measurements?
I know that the PE T110 (version 1) runs a socket 1156, but I bought two different socket 1156 heat sinks to replace the stock and realized that they don't fit. The screws are slightly wider than the...
View Articlepoweredge 6105 ip address configurations
can someone please help me with ip address configuration on the IPMI port of poweredge 6105 ?/
View ArticleCannot get 16 GB of RAM to work
We have a Dell PowerEdge 1900 Version 2 server. We are trying to install 16GB of RAM in the machine. We installed 2 GB sticks in the 8 slots but the machine is picking up the primary slots and not the...
View ArticlePowerEdge 2950 - generation ?
I got into my hands PowerEdge 2950 and I would like to know what is generation ...On front dont have labled any number in circle. But when i open OMSA 7.4 look like 2 gen.Baseboard Management...
View Article