Clear Error on PE R520 LED Display
I have a PSU0003 error on my PowerEdge R520's LED Display. The problem is resolved (pulled power plug while reconfiguring cables) but I don't know how to clear the error. Thanks for any help!
View ArticleBooting options in dell r610 poweredge with perc 6/i raid controller
hello sir, I have a new question about dell power-edge, actually i wanted to know this server is working on only raid configuration and for the safety purpose of data, are we able to use a...
View ArticleDell R610 reboots
I started getting these errors in the Server Manager event log as of recently and the server is rebooting and blue screens.A runtime critical stop occurred.A bus fatal error was detected on a component...
View ArticleDell R420
Hi Dell,I have issue with raid controller on my server dell r420. Installed two drives in RAID1 but only one(HDD) is blinking.Don't know what to do...
View Articlehow to upgrading R610 from 2.0.13 bios to 6.x.x
how to upgrading R610 from 2.0.13 bios to 6.x.x
View ArticleR420 Motherboards
What is the difference between these two motherboards for the R420? VD50G and 72XWF Thank you,
View ArticleDell power edge R815does not give display
Hi Everyone,We have Dell Power edge R815 server it were working fine and all of sudden its starting stuck, then we have to manually reboot the server. we did it for one to two days. Then we shutdown...
View Articleidrac upgrade / fan speed poweredge t620
I recently upgrade my idrac firmware to 2.10.10.10 from 1.46.45. Since then my fan speeds now run at 2000-2100rpm with normal load. Prior to the upgrade they were running at 1200rpm approx.I've tried...
View ArticlePower Edge 1650 - Dell Drivers & Update Disc
Hi,I'm looking for the last updated Dell Drivers & Update Disc for Power Edge 1650The one that you boot the server with to update all your hardware components Thanks
View ArticleClik here to view.
PowerEdge IOM Aggregator Firmware Updates?
Been looking all over and cannot for the life of me find any firmware updates for it.This is the product page:We are on 9.2 and it seems to make reference to 9.8, but there is no firmware downloads at...
View ArticleVLT0204 System board PS2 PG Fail voltage is outside of range.
I have a PowerEdge R520 with this error and found a thread here with a solution which includes taking the server to minimum configuration. The thread, "VLT0204 System board PS2 PG Fail voltage is...
View ArticleHOW CAN I ADD HARD DISK ON RAID 5/I - PowerEdge 2950
Hi all.We have a PowerEdge 2950, working on limit disk space.Is it possible to add 02 hard disks on that server without lost the content.How can I do this?Thanks so much in advance.
View ArticlePowerEdge 1950 - Foreign Configurations Found On Adapter
I do not know what has happened but two of my hard drives have failed on my 1950 I lost configuration files and disk is showing during boot up and cannot find my Centos 7:Foreign configurations found...
View ArticleR900 showing E1410 CPU 1 IERR and No Display
Hello Team,R900 with 2 CPU (2.4) 64Gb ram and SAS card.Suddenly it starts showing above error on LCD panel and stop working.Now No Display at all tried to reseat all parts but no luck.anyone share your...
View ArticleUpgrade memory on Dell PowerEdge R420
I have a Dell PowerEdge R420, 2 CPU Quad-Core Intel Xeon E5620 and 8 memories model HMT31GR7CFR4A-H9 installed.I want to upgrade the RAM on the system, adding 4 more HMT31GR7CFR4A-H9 module but not...
View Articlescript to retrieve CMC IP returns invalid address
Hello, I've been using this powershell script, VRTX_CMCIPAddress.ps1,...
View ArticleT410 Voltage Sensor fail
I have a T410 that shuts off after about 30 seconds with no errors or warnings, When I ran the Hardware Diags, the system failed with a failure code of: Error Code IPMI 2900:0221, MSG, <System...
View Articlemixed UDIMM RDIMM memory error when all memory is ECC Registered
We have an R620 which has 16 x 16GB. They were supplied originally by Dell and have the part number M393B2G70DB0 printed on them and so a quick google reveals this...
View ArticleClik here to view.
Can't show Storage - T420 - RAC0501 and RAC0503
Good morning!I have a problem, errors are shown in the menu 'Storage', in iDRAC.RAC0501 and RAC0503!As you can see below:Thank you!
View ArticleWhere to configure SNMP on iDrac 8?
Hi,We have a couple new servers and they showed up on some Security reports because their SNMP string was set to Public.I logged into the iDrac and went to Alerts, SNMP & Email, and changed the...
View Article