R620 with extra 5719QP card ports do not work on it.

Anyone using an R620 with both the integrated 5720 and 5719 QP cards for a total of 8 ports?

I am running Ubuntu 12.04 LTS (recently certified) and am not able to use eth4 through eth7.  I.e the ports on the 5917QP.  They appear to be up but they do not work.

The only odd thing I have noticed in dmesg is that ports 1 and 3 and 2 and 4 are sharing IRQs.  Not sure if that is correct.

[   28.720227] xen: registering gsi 66 triggering 0 polarity 1
[   28.720236] xen: --> pirq=66 -> irq=66 (gsi=66)

[   28.720261] tg3 0000:41:00.0: PCI INT A -> GSI 66 (level, low) -> IRQ 66
[   28.720372] tg3 0000:41:00.0: setting latency timer to 64
[   28.748878] tg3 0000:41:00.0: eth4: Tigon3 [partno(BCM95719) rev 5719001] (PCI Express) MAC address 00:10:18:f4:9d:c4
[   28.749019] tg3 0000:41:00.0: eth4: attached PHY is 5719C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1])
[   28.749159] tg3 0000:41:00.0: eth4: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1]
[   28.749291] tg3 0000:41:00.0: eth4: dma_rwctrl[00000001] dma_mask[64-bit]
[   28.749476] xen: registering gsi 68 triggering 0 polarity 1
[   28.749485] xen: --> pirq=68 -> irq=68 (gsi=68)
[   28.749511] tg3 0000:41:00.1: PCI INT B -> GSI 68 (level, low) -> IRQ 68
[   28.749621] tg3 0000:41:00.1: setting latency timer to 64
[   28.767124] tg3 0000:41:00.1: eth5: Tigon3 [partno(BCM95719) rev 5719001] (PCI Express) MAC address 00:10:18:f4:9d:c5
[   28.767286] tg3 0000:41:00.1: eth5: attached PHY is 5719C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1])
[   28.767419] tg3 0000:41:00.1: eth5: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1]
[   28.767550] tg3 0000:41:00.1: eth5: dma_rwctrl[00000001] dma_mask[64-bit]
[   28.768541] xen: registering gsi 66 triggering 0 polarity 1
[   28.768546] Already setup the GSI :66
[   28.768649] tg3 0000:41:00.2: PCI INT A -> GSI 66 (level, low) -> IRQ 66
[   28.768760] tg3 0000:41:00.2: setting latency timer to 64
[   28.816489] tg3 0000:41:00.2: eth6: Tigon3 [partno(BCM95719) rev 5719001] (PCI Express) MAC address 00:10:18:f4:9d:c6
[   28.816627] tg3 0000:41:00.2: eth6: attached PHY is 5719C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1])
[   28.816760] tg3 0000:41:00.2: eth6: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1]
[   28.816896] tg3 0000:41:00.2: eth6: dma_rwctrl[00000001] dma_mask[64-bit]
[   28.817083] xen: registering gsi 68 triggering 0 polarity 1
[   28.817087] Already setup the GSI :68
[   28.817182] tg3 0000:41:00.3: PCI INT B -> GSI 68 (level, low) -> IRQ 68
[   28.817293] tg3 0000:41:00.3: setting latency timer to 64
[   28.868364] tg3 0000:41:00.3: eth7: Tigon3 [partno(BCM95719) rev 5719001] (PCI Express) MAC address 00:10:18:f4:9d:c7
[   28.868502] tg3 0000:41:00.3: eth7: attached PHY is 5719C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1])
[   28.868635] tg3 0000:41:00.3: eth7: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1]
[   28.868764] tg3 0000:41:00.3: eth7: dma_rwctrl[00000001] dma_mask[64-bit]

Any ideas out there?

Thanks

Carlos